10 Must-do Repairs Before Selling
By James Wedgeworth on October 23rd, 2008
circle that you’ll stack directly on top of the first. (Also at the store, purchase two new bolts — about $1.50 each.) Back home, remove the old gaskets. Fit the new shaped gasket into the mouth of the sewer pipe first; put the second seal directly over it so the toilet fits into the space with no gaps. Lower the toilet over the seals. Screw in the new bolts, tighten them, reconnect the water supply and caulk the base of the toilet.
8. Stop faucet drips.
A dripping faucet calls attention to itself, and it’s not hard to fix. Shut off the water supply to the faucets by turning the valves under the sink to the right. Then, test the faucet to make sure you’ve shut the water off completely. While you’re looking under the sink, check for moisture on the wall around the valves and on the floor of the sink cabinet. Also check the supply lines leading to the dishwasher and disposal. If those areas are wet, get a plumber.
If you’ve got a newer, rotating, single-arm faucet (through which both hot and cold water run), note the brand and purchase a faucet rebuild kit (roughly $50) at the hardware store. Inside the faucet arm is a metal ball on a stem that lets the handle swivel while allowing water to flow in any direction. The kit contains the six to 12 parts most likely to fail, including that metal ball, O rings, springs and gaskets. The idea is to replace them all rather than trying to diagnose the exact source of the problem. Dismantle the faucet, laying the parts out in order on a paper towel. Snap a photo or draw a sketch to help you with reassembly. Replace the old parts, put the faucet back together and turn the water back on.
For older faucets with independent hot and cold water faucets, shut off the water under the sink as before then dismantle each of the sink’s faucets separately. Remove the washers (rings made of rubber, plastic or brass), put them in a plastic sandwich bag and bring them to the hardware store to find replacements. Reassemble the faucets and turn the water back on.
If this seems like more trouble than you’re willing to tackle, call a plumber. With no complications, a plumber can install the new parts in an hour, though most will bill you for an hour and a half minimum.
9. Renew dinged baseboards.
Beat-up baseboards detract greatly from the appearance of your home, and they’re easy to spiff up. “All those little things tend to stand out,” says Carroll. First, clean them to remove scrapes and smudges left by clawing pets and toddlers on wheels. Brake says a Mr. Clean Magic Eraser sponge works great on painted surfaces. Fill in dents with spackle, sand the baseboards smooth and repaint them. If you’ve lost the name of the original paint color, chip off a coin-sized bit, slip it into an envelope and bring it to the paint store where you can have the color computer matched.
Use primer before painting. Don’t just retouch small areas; paint the entire piece of baseboard, from one end to the other. Choose a washable eggshell finish. White is a great choice for making baseboards and trim look crisp and clean.
10. Repair cabinet scratches.
You can quickly improve the look of unpainted woodwork and worn cabinets with an application of products that even out the surface color. Brake covers scratches on woodwork and cabinets with Old English Scratch Cover or a Tibet Almond Stick, a tight roll of cotton saturated in chemicals that the manufacturer, Zenith Chemical Works, says is a 100-year-old family formula. (You can find these at hardware and home-improvement stores.)
The almond stick goes on clear but covers scratches. “It’s amazing,” Brake says. Zenith owner Kim MacInnes says the almond stick works best with shallow surface scratches on dark finishes. It doesn’t work in every case, he says, and even a good result may fade with time and need to be reapplied periodically.
Old English makes separate formulations for light or dark wood. These are oily stains, so use them carefully. Try out any products first in a corner where results will not be noticed. Do not use the dark stain on light wood. Finally, polish wood cabinets to a glow with lemon oil.
Courtesy of MSN Real Estate
[...] Many of us watch TV shows and see the miraculous transformation of homes and gardens by professionals and amateur do-it-yourselfers. Is it really that easy, we ask ourselves. Could I do it? Where do I begin? What improvement projects will generate the biggest increase in the value of my home? Home … 10 Must-do Repairs Before Selling [...]
[...] … is the weight, compared with a normal roof that weighs 750 pounds per 100 square feet, metal roofs range from 50-150 pounds per 100 square feet. Because of this, you can easily install a new roof over the last one without the costly and time consuming task of taking off the old roof. Metal roofs … 10 Must-do Repairs Before Selling [...]
[...] … make minor changes that will create impact. If you can’t replace the kitchen cabinets, replace the cabinet doors at least. If that is also beyond your means, add molding to the cabinet doors, paint them, and replace the hardware. It’s not that difficult or expensive to replace an outdated sink … 10 Must-do Repairs Before Selling [...]
[...] … for above the toilet. Caution when buying Kohler hardware: the stems will not adapt to non-Kohler valves. I had to replace the tub/shower valve within the wall before I could install the Memoirs hardware, at a total cost of over $800 for just the valves and new copper piping. The actual Memoirs … 10 Must-do Repairs Before Selling [...]